TR4110M / TR4111
100k - 4.5GHz
后面板
TR4110M / TR4111A
10k - 4.5GHz
后面板TR4110M / TR4111
|
后面板TR4110M / TR4111A
|
后面板TR4110 / TR4113
|
尺寸: 43x18x48cm
重量: 20kg
CRT 特性
动态范围 50dB
TR4110 :
P7 persistence 400 ms
尺寸 10 x 8 cm (10 x 8 div.)
TR4110M :
Half-tone type storage tube, acceleration voltage 7.5kV, P31 phosphor; 尺寸 9.5 x 7.6cm(10 x 8 div.)
Amplitude 特性
Reference level indication : +40 dBm to -60 dBm steps. Indication in dBμ; is optional.
IF gain :
0 dB to 60 dB in 10 dB steps;
0 dB to 12 dB in 1 dB steps;
Continuously variable by ±1.5
dB or more by means of the VARI. control.
Reference level indication accuracy : ±0.5 dB
LOG. indication accuracy :
±0.15 dB/1 dB,
±0.5 dB/10 dB,
±1.5 dB/70 dB
Level stability : 0.1 dB/oC (for IF band width of 300 kHz)
Warning indication : LED indication
Video filter : Selectable from 10 Hz, 100 Hz, 10 kHz and OFF.
Scan 特性
Scan mode : Selectable from SINGLE, EXT, INT and MANUAL modes.
Scan tringger : Selectable from the AUTO, LINE, EXT and VIDEO modes, only when the scan mode is set
at INT.
Scan time 特性
Scan time : 20 μs/div.to 10 s/div.in a 1-2-5 sequence,and manual scan.
Scan time accuracy : 15%(at full scan)
Scanning indication : LED indicator
Output 特性
X-axis output :
Output impedance approx.1kΩ
Output level 5±V
Y-axis output :
Output impedance Approx. 5kΩ
Output level 3 Vp-p at full scale
Z-axis output : Output level blanking at low TTL level
TR4110M四种显示模式
NORMAL : Used as a non-storage tube.
PERSISTENCE :
Variable range MIN 500 ms
MAX 15 sec.
Hold 120 sec.
STORE :
MIN 1 min.
MAX 1 hour.
ERASE :
Possible in the PERSISTENE mode;
approx.1 sec.
Warm-up time :
Approx.1 min.(CRT)
Probe power : ±15 v, 4 pin connector
Frequency axis 特性
TR 4111A : Measurement possible in range A, B,or C
TR 4113A : Measurement in range A only
TR 4111A : 10kHz to 4.5 GHz
TR 4113A : 10kHZ to 1.7 GHz
Center frequency indication : 7-segment LED indication in four digits.
Indication resolution :
Range A : 1 MHz
Range B : 10 MHz
Range C : 10 MHz
Switchable between START and CENTER.
Center frequency indication accuracy :
Range A : ±10 MHz With the use of Zero Cal. ±5 MHz
Range B : ±30 MHz With the use of Zero Cal. ±20 MHz
Range C : ±30 MHZ With the use of Zero Cal. ±20 MHz
Scan width : 200 MHz/div. to 200 Hz/div. in a 1-2-5 sequence 19 stages
Frequency response :
Range A : 10 kHz to 1000 MHz ±1 dB ; 10 kHz to 1700 MHz ±1.5 dB
Range B : ±1.5 dB
Range C : ±1.5 dB
Scan linearity : Within ±10%
IF band width (Resolution band width) : 30 Hz to 300 kHz in a 1-3 sequence in 10 stages and AUTO (by the OPTI_MUM SELECTOR)
IF band width accuracy : ±25% (for a band width of 3 dB)
IF band width selectivity : 3 dB : 60 dB ratio < 1 : 15 (30Hz to 300 kHz)
IF band width switching accuracy : Within ±1 dB (between 10 Hz and 300 kHz with a temperature between 20 ℃ and 30 ℃ )
Sweep mode :
Frequency stability :
Noise side band :
With the VIDEO FILTER set at 10 Hz, an average noise level, and a room temperature of 23℃ ±10℃,
and the STABILIZER ON;
-70 dB or less (for 1 kHz IF band width and 20 kHz deviation from the carrier)
-55 dB or less (for 100 Hz IF band width and 2 KHz deviation from the carrier)
Amplitude 特性
Scale selection on the screen :
Switching between LOG. (dB scale) and LIN. (linear scale).
LOG. is graduated for 10 dB/div., 5dB/div., 2dB/div., and 1 dB/div.
动态范围 :
Average noise level; -115 dBm or less (for 1 kHz IF band width with VIDEO FILTER set to 10 Hz)
Spurious response; -70 dB or less (at range A, 5MHz to 1700MHz, and an input of -30 dBm)
Residual response; -100 dBm or less
Gain compression : 0.5 dB or less (for an input of -10 dBm)
输入特性
输入口 : N 型
输入阻抗 : 50Ω (with input ATT set to 10 dB and input VSWR at 1.5 or less)
输入衰减 : 0 dB to 40 dB in 10 dB steps
最大输入电平 : +20 dBm, ±25 VDC (with RF ATT set to 10 dB or more)
输出特性
校准输出 :
Frequency 50 MHz ±10 kHz with 1 MHz comb signal included.
Reference signal level -20 dBm ±0.5 dB. Output power is provided by the CAL. OUT terminal.
咨询电话: 132- 4173- 5460 , 邮箱: 52634729@QQ.com
